BIKE SELECTOR

20 of 21 search results

Sort on:

Used to plug the crankcases professionally when the tappet covers are removed. Complete with nylon screws for installation. These do a perfect job of keeping dust and debris out of the engine. And stuffing the crankcase with paper or rags? Those days are over!
9 Finger Fabrication LLC

9Finger Fabrication, M8 lifter bore case cover set

#998407

Stock:Yes

Used to plug the crank position sensor hole in the crankcase to prevent dirt or debris entering the engine case. The captured 1/4-20 nylon bolt makes sure the plug and bolt will not be separated. Note: This is not a flywheel locking tool.
9 Finger Fabrication LLC

9Finger Fabrication, CKP sensor hole plug

#998418

Stock:Yes

Used to plug the crankcases professionally when the tappet covers are removed. Complete with nylon screws for installation. These do a perfect job of keeping dust and debris out of the engine. And stuffing the crankcase with paper or rags? Those days are over!
9 Finger Fabrication LLC

9Finger Fabrication, Twin Cam lifter bore case cover set

#998409

Stock:Yes

Used to plug the crankcases professionally when the lifter blocks are removed. Complete with nylon screws for installation. These do a perfect job of keeping dust and debris out of the engine. And stuffing the crankcase with paper or rags? Those days are over!
9 Finger Fabrication LLC

9Finger Fabrication, Evo/Shovel lifter bore case cover set

#998411

Stock:Yes

Keep the crap out of your engine while oil filter is removed. O-ring sealed with transfer ports that allow oil flow if engine is turned over with cover installed.
9 Finger Fabrication LLC

9Finger Fabrication, oil filter cover

#998417

Stock:Yes

Fully adjustable for brake pedal height. Direct replacement for the stock non-adjustable brake linkage. Allows adjustments of the brake pedal from 3-1/2" lower to 1-1/2" higher to compensate for seating height, rider length and preference. Provides quicker and more comfortable brake actions. Stainless steel, complete with heavy duty heim joints.
9 Finger Fabrication LLC

9Finger Fabrication, M8 mid-control brake linkage. Polished

#998415

Stock:Yes

Fully adjustable for brake pedal height. Direct replacement for the stock non-adjustable brake linkage. Allows adjustments of the brake pedal from 3-1/2" lower to 1-1/2" higher to compensate for seating height, rider length and preference. Provides quicker and more comfortable brake actions. Stainless steel, complete with heavy duty heim joints.
9 Finger Fabrication LLC

9Finger Fabrication, M8 mid-control brake linkage. Black

#998414

Stock:Yes

Used to professionally cover the exhaust ports to keep dust and debris out of the engine. Stuffing paper or rags down the exhaust ports? Those days are over!
9 Finger Fabrication LLC

9Finger Fabrication, Shovelhead exhaust port cover set

#998402

Stock:Yes

Used to professionally cover the exhaust ports to keep dust and debris out of the engine. Stuffing paper or rags down the exhaust ports? Those days are over! Note: For the exhaust port cover set see 998404 for 84-99 Evo B.T; 86-22 XL; 99-17 Twin Cam or 998403 for 17-up M8
9 Finger Fabrication LLC

9Finger Fabrication, exhaust port cover set

#998401

Stock:Yes

Used to store the hydraulic lifters (hydraulic tappets). Tool is position marked so, after the work is done, the lifter can be reinstalled in the same bore. This ensures best tappet performance. The hold down arm keeps the lifters firmly in place. Magnetic holes are provided to store the anti-rotation pins as used on Twin Cams models. USA made.
9 Finger Fabrication LLC

9Finger Fabrication, lifter organizer

#998399

Stock:Yes

Used to hold the hydraulic lifters (hydraulic tappets) in the tappet bores when removing the camshaft or to remove the lifters up & out of the engine. The tool is adjustable, allowing deeper penetration, no more pushing up the lifter to meet the magnet. The strong magnets allow you to pull tappet blocks and lifters out as a unit on Evolution engines. Helps prevents hydraulic lifters to be accidentally switched to another tappet bore position, this ensures best tappet performance. USA made.
9 Finger Fabrication LLC

9Finger Fabrication, Magnetic Adjustable Lifter Holder Set

#998397

Stock:Yes

Plug 'm! The only right way to cover up the bore openings when the pushrod tubes are removed. Foreign material that inadvertently gets into the tappet bores is not what you want. O-rings keep a tight seal in the tappet bores and hold the plugs in place.
9 Finger Fabrication LLC

9Finger Fabrication, Tappet Block Plug Set

#998398

Stock:Yes

For rear 530 chain driven bikes. Used to lock the main drive gear and sprocket and allows proper torquing and removal of the sprocket nut, without using the uncontrollable force of an impact wrench.
9 Finger Fabrication LLC

9Finger Fabrication, Chain Drive Sprocket Locking Tool

#998413

Stock:Yes

Plug 'm! The only right way to cover up case bore openings. Foreign material that gets into the bottom end can cause major damage, using a rag or shop towel can inadvertently introduce these contaminates. This magnetic case bore plug set fits the spigot perfectly, holds the rods and is sold in a 4-pack set for front & rear cylinder. - Range: 3.625" to 3.950" crankcase bore.
9 Finger Fabrication LLC

9Finger Fabrication, Evo/Shovel/XL case bore plug set

#998396

Stock:Yes

Used to professionally cover the intake ports to keep dust and debris out of the engine. Stuffing paper or rags down the intake ports? Those days are over! Note: See 998401 for the exhaust port cover set.
9 Finger Fabrication LLC

9Finger Fabrication, M8 intake port cover set

#998403

Stock:Yes

Used to professionally cover the intake ports to keep dust and debris out of the engine. Stuffing paper or rags down the intake ports? Those days are over! Note: See 998401 for the exhaust port cover set.
9 Finger Fabrication LLC

9Finger Fabrication, Evo/Twin Cam intake port cover set

#998404

Stock:Yes

When the air cleaner is not installed, this cover is used to professionally cover the intake of the throttle body to prevent dust & debris entering the engine. Stuffing paper or rags down the intake? Those days are over!
9 Finger Fabrication LLC

9Finger Fabrication, M8 throttle body intake cover

#998419

Stock:Yes

Used to simplify getting your engine sprocket, clutch basket and primary chain all in perfect alignment when changing or checking any drivetrain components. Multiple standoff lengths allow use on all models from early Shovel to M8.
9 Finger Fabrication LLC

9Finger Fabrication, primary chain alignment tool

#998416

Stock:Yes

Plug 'm! The only right way to cover up case bore openings. Foreign material that gets into the bottom end can cause major damage, using a rag or shop towel can inadvertently introduce these contaminates. This magnetic case bore plug set fits the spigot perfectly, holds the rods and is sold in a 4-pack set for front & rear cylinder. - Range: 4.00" to 4.300" crankcase bores.
9 Finger Fabrication LLC

9Finger Fabrication, Twin Cam case bore plug set

#998395

Stock:Yes

Used to pre-bleed the hydraulic units, to help prevent valve train damage after initial engine start due to incomplete bled tappets. Simply load lifters in basket, set in vacuum jar, top with clean engine oil, tighten lid and apply vacuum such as a brake bleeder and watch all the air bubbles float away. Includes basket, jar and lid.
9 Finger Fabrication LLC

9Finger Fabrication, Lifter Bleed Tool

#998400

Stock:Yes