BIKE SELECTOR

20 of 989 search results

Sort on:

For 547090 chain breaker tool
Motion Pro

Motion Pro, repl. body bolt

#547094

Stock:Yes

Fits 48mm fork tubes; Carbon steel with aluminum lock ring; Used to drive fork seals into lower fork leg without hassle; Easy 2-piece design
Motion Pro

Motion Pro, Ringer fork seal driver 48mm forks

#547712

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 19mm

#580882

Stock:Yes

Used to remove the press-fitted tappet blocks from the right side of the Sportster crankcase. Replaces OEM 95724-57 tool.
Jims

JIMS, tappet block puller tool

#978308

Stock:Yes

Prevents clutch hub from rotating when installing/removing clutch hub nut.
Jims

JIMS, clutch shell lock tool

#978344

Stock:Yes

Used to remove & install the slotted lock nut, on wire wheels (spoked wheels) with drum brakes, to correct torque
Jims

JIMS, wheel bearing lock nut socket

#978379

Stock:Yes

Blue powder coated steel. In many later H-D models rubber mounted engines are a structural part of the frame. With the engine removed it becomes impossible to roll the bike, which can be awkward in a workshop. When the 'Rollin Buddy' is installed it bolts the chassis back together and it is possible to roll the bike as if the motor was installed and keeps your work floor and bike lifts free of incapacitated motorcycles.
Jims

JIMS, 'Rolling Buddy' engine mount

#978629

Stock:Yes

Used to lock flywheel, of assembled engine. Installs through crank position sensor. Great for use with compression leakdown testing and other service operations where flywheels must be locked. Note: Incl. highly visible red 'Danger, do not operate' card to prevent someone starting engine.
Jims

JIMS, 'Mighty Bite' flywheel lock

#559408

Stock:Yes

Dual spindle; Used to machine cases for high lift cams
George's Garage

George's Garage, cam relief tool

#979419

Stock:Yes

Single spindle; Used to machine cases for high lift cams
George's Garage

George's Garage, TC cam relief tool

#979418

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 21mm

#580881

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 17mm

#580883

Stock:Yes

Must be ordered separately for 978324 JIMS sprocket shaft seal installer tool. Is included with 978325 JIMS maindrive seal installer tool.
Jims

JIMS, driver handle

#576558

Stock:Yes

Used to pull the main drive gear bearing straight from the transmission case, without damage or removing the case from the frame
Jims

JIMS, 5-speed transmission main bearing puller

#978360

Stock:Yes

Used to install cam bearing. Note: MCS 920542 installation handle is required and sold separately.
Jims

JIMS, cam bearing installer tool

#978289

Stock:Yes

Used to correctly align ignition switch housing for installation.
George's Garage

George's Garage, ignition switch housing tool

#979475

Stock:Yes

Used instead of rags. Provides enough plugs to fully seal all Twin Cam and transmission holes to prevent dirt and dust from entering while it is apart during a rebuild or repair.
Jims

JIMS, engine & transmission plug kit

#962014

Stock:Yes

Blue powder coated steel. In many later H-D models rubber mounted engines are a structural part of the frame. With the engine removed it becomes impossible to roll the bike, which can be awkward in a workshop. When the 'Rollin Buddy' is installed it bolts the chassis back together and it is possible to roll the bike as if the motor was installed and keeps your work floor and bike lifts free of incapacitated motorcycles.
Jims

JIMS, 'Rolling Buddy' engine mount

#978630

Stock:Yes

A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care, as you would treat a micrometer.
Jims

JIMS, balancer shaft alignment tool

#978416

Stock:Yes

Used to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With 1/2" drive; Note: Use with hand drivers only. Not to be used with power tools.
Jims

JIMS, sprocket shaft engine rotator

#978501

Stock:Yes