Motorcycle Storehouse

Select your bike

BIKE SELECTOR

20 of 38 search results

Sort on:

Sort on:

The TestMate provides within seconds a professional assessment of the state of health, state of charge and CCA capability of a 12V battery. The TestMate is compact, light, and can be used in the workshop or at the sales counter.
- Professional affordable 12V battery tester
- Up to 200 Ah batteries
- Select battery type and Ah / CCA, then TEST
- For all battery technologies (Lead Acid, AGM, GEL)
- Result available in seconds
- Rugged, ideal for workshop use

Tecmate Testmate Auto 2 battery tester

#941509

Stock:No

Monitor cable for Lithium batteries. 60cm long. With M6 / 1/4" ringlets to 2-pin SAE connector with waterproof sealing cap.
- Micro processor driven 4 LED system used to monitor battery status.
- Informs you if the battery is in a good/needs charge/not good condition
- When the engine is running it also informs you if the vehicle's charging system is working. Then the LED mode changes to an arrow, with the pointer reaching the LED matching the voltage being delivered by charging system. No arrow means there is no charge
- A bright red LED warns that the charge level has reached 50% and that it is time to recharge that battery
- During vehicle storage the LED matching the battery’s state of charge will blink every 5 seconds, drawing very little power (0.2 milli-amps) to do so, in fact 20-100 times less than the vehicle’s circuitry is drawing from the battery at the same time
- Fast blink mode for first 15 seconds after connection to battery, for quick check of multiple batteries (e.g. vehicles on showroom floor)

Tecmate OptiMATE Monitor O-127 cable. Lithium

#941815

Stock:Yes

Straight socket. Fast charge 2 mobile devices at the same time. Fits into a standard BIKE power socket of BMW, Triumph or Ducati MultiStrada.
- Connects to a standard BIKE (DIN Ø12mm) power socket
- Weatherproof
- Offers 2 x 3300mA fast charge USB power
- Auto-off 3 hours after engine stopped or if battery voltage drops below 12.3V, to protect the vehicle battery

Tecmate OptiMATE USB O-115 USB charger

#941549

Stock:Yes

'State of Charge' battery tester. For all 12V lead-acid & 12.8V/13.2V lithium batteries. Used to quickly see the battery's charge condition before a battery is sold, or when it is returned.
- State of charge result in Volts and %, 3 different bands for Lead Acid, AGM/GEL and LiFePO4 4 series batteries
- Easy to follow instructions on rear panel of the tester
- Easily connects with connect clips to the battery or to an installed SAE 2-pin battery lead.
- Industry standard SAE 2-pin connector
- 100cm battery clip set
- Flashing indicator for discharged battery

Tecmate OptiMATE, Test TS126 battery tester

#941420

Stock:Yes

With EU wall plug. Professional 4-bank battery saving charger for power sport & small engine 12V batteries. No further battery knowledge required. Connect up to 4 x 12V batteries and let the charger do the rest.
- OEM recommended battery care center for correct activation of new batteries and recovery, charge and testing of neglected sulphated / low-voltage batteries.
- New mode: a 1 hour activation charge only for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ‘dry-charged’ batteries that are delivered with a separate custom acid pack
- Charging Amps: 4A maximum, Ampmatic control. (2A max. when 2A is selected)
- Use: Indoor / workshop environment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 1.8V + 2 step desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 2 – 40Ah
- Selectable 110-120V / 220-240V 50-60Hz
- Vented industrial table top case.
- Incl. 6ft / 180cm AC supply lead and 4 x 6ft / 180cm charge lead ending in SAE connector. 4 x standard battery clip sets
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, Pro 4 battery charger. 12V

#941416

Stock:Yes

With EU wall plug. Professional 8-bank battery saving charger for power sport & small engine 12V & 6V batteries, including neglected sulphated / low-voltage batteries. Once voltage selection has been made, no further battery knowledge required. Connect up to 8 x 6V and 12V batteries and let the charger do the rest.
- The OEM recommended 8-bank battery care center for recovery, charging and testing of all 6V and 12V batteries, including neglected sulphated / low-voltage batteries
- 8-bank charger, each bank operates independently
- Select battery voltage of 6V or 12V for each bank
- 1Ah charging Amps per bank
- Use: Indoor / workshop environment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 1.8V + 2 step desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 2Ah
- Selectable 110-120V / 220-240V 50-60Hz
- On/Off power switch and replaceable fuse protection
- Vented industrial table top case.
- Incl. 6ft / 180cm AC supply lead and 8 x 6ft / 180cm charge lead ending in SAE connector. 8 x standard battery clip
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected
- Use: Indoor / workshop environment (lowest temperature: -4°F / -20°C)

Tecmate OptiMATE, Pro 8 battery charger. 12V/6V

#941417

Stock:Yes

With EU wall plug. 4-bank x 8-step 12.8/13.2V 0.8A Battery saving charger-tester-maintainer. Charges up to 4 x LiFePO4 / LFP (Lithium Iron Phosphate) 4-series batteries with nominal voltage of 12.8V – 13.2V. Each bank charges independently.
- Saves low voltage LiFePO4 batteries
- Specialized LiFePO4 charge cycle
- Maintains & protects LiFePO4 batteries
- Battery BMS (Battery Management System) reset
- Charging Amps: 0.8A per bank
- Indoor & Outdoor invironment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 0.5V + 3 step low volt save & test
- For LiFePO4 (LFP) 4 series cell 12.8 / 13.2V batteries from 2 – 30Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 4 x 6ft / 180cm charge lead ending in SAE connector. 4 x Weatherproof battery lead & 4 x standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, Lithium 4s 0.8A 4-bank

#941409

Stock:Yes

With EU wall plug. 4-step 6V/12V ChargeMatic Battery charger-maintainer. Will charge any 6V or 12V lead-acid battery, both starter and deep cycle. Temperature protected charger with IUoU 4-step charging program, including reversion from 'maintenance' float stage if high current is drawn during storage charging. Simply select 6 or 12 voltage, hook up the battery and this temperature compensated, 4-step charger will do the rest.
- Charging Amps: 1.2A (temperature protected)
- 4-step. Bulk, Absorption, maintain & revert
- Indoor (lowest temperature: -4°F / -20°C)
- Low Volt Start of 2V for 6 or 12V batteries
- For 6V & 12V Lead Acid, AGM, GEL lead-acid batteries, starter and deep cycle, up to 50Ah
- EU 220-240V 50-60Hz North America: 110-120V 50-60Hz.
- Standard case (vented)
- Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector, a fused battery lead & standard battery clip set
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, AccuMate 6/12 1.2A battery charger

#941412

Stock:No

With EU wall plug. The power sport OEM recommended load tester, power desulphator and charger for all types of 12V lead-acid batteries. The BatteryMate has been saving batteries for 25 years!
- New battery activation – 30 minute activation charge for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ‘dry-charged’ batteries that are delivered with a separate custom acid pack
- True load tester selectable from 15A to 150A – Automatically tests battery cranking amps up to 330CCA. 3 second test simulates normal engine cranking / start, 15 second test checks battery health
- Powersport specific charging algorithm – 4 step charging method recovers any 12V battery. MF mode allows up to 16.9V for ‘dry-charged’ AGM batteries
- Temperature regulated charging – Charge voltage is adjusted according to ambient temperature. (-4mV/°C/cell above/below 68°F/20°C)
- Accurate voltage sensing. Charge leads have integrated voltage sense wires for exact voltage measurement at the battery
- Easy to use. 6 position combination selector allows selection of correct test and charge current for connected battery. TEST and then select max. charge time according to result, press 'charge' button. Program completes charging automatically and then tests the battery
- Charging Amps: 9A maximum; 1, 2, 3, 5, 7, 9 Amp selection
- Testing Amps: 150A maximum; 15, 35, 50, 70, 100, 150 Amp selection
- Indoor / workshop environment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 1V + high power desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 2 – 40Ah
- Selectable 110-120VAC / 220-240VAC 50-60Hz
- On/Off power switch and replaceable fuse protection
- Vented industrial table top case
- Incl. 6ft / 180cm AC supply lead and 1 pair high current 6ft / 180cm charge leads ending in heavy duty battery clamps
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, BatteryMate 150/9 battery charger

#941415

Stock:Yes

Battery clips with a 15A fuse, with ‘easy grip’ rubber handles, custom designed to fit round, square (power sport) and flat tab posts.
- Length=20"/50cm
- Industry standard SAE 2-pin connector
- 15A fuse
- Cable max. rating: 10 Amp
- -40°C/-40°F low temperature use. Cable remains flexible at ‘below freezing’ temperatures
Note: Includes in-line rubber seal for OptiMATE heavy duty SAE connector.

Tecmate, OptiMATE battery charge cable O-14

#941546

Stock:Yes

With EU wall plug. 10-step 12.8V/13.2V 6A battery saving charger-tester-maintainer. The ultimate LiFePO4 / LPF Lithium Iron Phosphate) professional level battery diagnostic & maintenance charger and tester for batteries from 3 to 72 Amp-hour.
- 10 steps: 1 low volt start (0.5V); 2 Test before charge; 3 Temperature check; 4 Ultra low volt save; 5 cell monitoring; 6 Test cell damage; 7 cel-balancing charge; 8 Optimize; 9 Test after charge; 10 24-7 maintenance
- Starts from 0.5V with continuous monitoring / testing of charge acceptance or bad / shorted cell condition. Unnecessary (and unsafe) charging of a bad battery is prevented
- Indoor / Outdoor (lowest temperature: -40°F / -40°C)
- Input 100-240V 50-60Hz, high efficiency (CEC listed)
- Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector
- Low Volt Start of 0.5V + 3 step low volt save & test
- Includes weatherproof battery lead & battery clip set
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, Lithium 4S 6A battery charger

#941406

Stock:Yes

With EU wall plug. 6-step 12V battery to 12V battery charger. Used to charge your trailered motorcycle, ATV or speedboat from another battery. Will work with 12V (lead acid) or 12.8-13.2V (LFP-Lithium) batteries.
- 2A charging Amps
- For Indoor & Outdoor (lowest temperature: -4°F / -20°C)
- Saves deep discharged, sulfated batteries
- Low Volt Start from 2V
- For STD, AGM & GEL 12V batteries and LFP 12.8V-13.2V batteries from 3 – 96Ah.
- Input: 12-16 V, 2.7A max
- Long term maintenance mode protects the source battery, drawing only when the battery under charge needs it. Charging will stop when source battery voltage is below 12.2V.
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm DC supply lead and 6ft / 180cm charge lead ending in SAE connector. Weatherproof battery lead, standard battery clip set & fused battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Safe for vehicle electronics
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, DC to DC battery charger

#941411

Stock:Yes

With EU wall plug. 8-step 12.8/13.2V 0.8A Battery saving charger-tester-maintainer. Used to charge LiFePO4 / LFP (Lithium Iron Phosphate) 4-series batteries with nominal voltage of 12.8V – 13.2V.
- Saves low voltage LiFePO4 batteries
- Specialized LiFePO4 charge cycle
- Maintains & protects LiFePO4 batteries
- Battery BMS reset.
- Charging Amps: 0.8A
- Indoor & Outdoor (lowest temperature: -4°F / -20°C).
- Save: Low Volt Start of 0.5V + 3 step low volt save & test
- For LiFePO4 (LFP) 4 series cell 12.8 / 13.2V batteries from 2 – 30Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector. Weatherproof battery lead & standard battery clip set
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE Lithium battery charger

#941408

Stock:Yes

Combination 2400mA USB charger and 3-LED battery monitor, with vehicle battery protection.
- Vehicle battery protection: USB output turns off 3 hours after engine stopped or when vehicle battery charge level is less than 50%
- 3 LED battery monitor (when USB output off) – battery status is displayed every 5 seconds
- 12V input through an industry standard SAE 2-pin connector
- 5V 2400mA true output
- Unique seal and cap design for USB socket ; use any USB cable, seals when inserted
- Short circuit, overheat, over-voltage protection

Tecmate OptiMATE USB O-100 USB charger

#941547

Stock:Yes

With EU wall plug. 9-step 10Amp battery charger for 12V Lead Acid, AGM, GEL starter & Deep Cycle batteries from 3 – 400Ah that demand accurate temperature controlled charging and unsupervised safe long term maintenance. Voltage selection (14.4V / 14.7V) ensure the battery receives charge at the correct voltage. Ampmatic charge control adjusts current to suit any battery size or condition for fastest and most complete charge i.e. small batteries receive less current, large batteries up to maximum current.
- 'Power Supply' mode delivers stable power for vehicle system reprogramming, show room vehicle demo or retaining memorised settings when battery cables are disconnected to fit powered accessories or replace the battery
- Charging Amps: 10A (AmpMatic)
- Ampmatic: Microprocessor adjusts charge current to match battery size / condition for perfect LiFePO4 charge curve, for fastest and most complete charge
- Selectable charge: 14.4V for standard lead acid batteries / 14.7V for premium AGM or Deep Cycle
- Save: Low Volt Start of 0.5V + 2-step desulphation recovery
- For Lead Acid, AGM, GEL & Deep Cycle 12V batteries from 3 – 400Ah
- Powersupply 13.6V
- Indoor / Outdoor (lowest temperature: -40°F / -40°C)
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector. Weatherproof battery lead & standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE 7, Select battery charger

#941405

Stock:Yes

With EU wall plug. 9-step 12V 5A Battery Saving charger-tester-maintainer. Saves batteries other chargers can’t, because it recognizes the difference between a discharged battery that needs charging and a dead flat sulphated battery that needs saving. Perfect for months-long maintenance of any lead-acid, AGM, GEL & deep cycle 12V batteries from 3 – 240Ah.
- Cell voltage balancing mode: correctly prepares new batteries for first use and optimizes battery performance
- Daily battery condition tests & interactive float charge: maintains battery fully charged, weeks or months long
- Charging Amps: 5A (Ampmatic)
- Ampmatic charge control: adjusts current to suit any battery size (3 to 240Ah) or condition for fastest and most complete charge
- Indoor / Outdoor (lowest temperature: -40°F / -40°C)
- Save: Low Volt Start of 0.5V + 2-step desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 3 – 240Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector. Weatherproof battery lead & standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE 6, Ampmatic battery charger

#941207

Stock:Yes

9 step 12V / 12.8V 1.25A sealed battery saving charger & maintainer for AGM, GEL & STD 12V batteries from 4 – 60Ah & Lithium (LiFePO4) 12.8/13.2V batteries from 2 – 15Ah. OptiMate 4 Quad Program tests before & after charging and can recover a ‘dead-flat’ lead-acid & lithium (LiFePO4) battery from as low as 0.5 Volts.
- Selectable, 4 charge programs: 1).12V Smart desulphation: 0.5V - 14.4V.
2). BMW CAN-bus compatible: 5V - 14.4V.
3). 12.8V Low Volt Recovery: 0.5V - 14.4V.
4). BMW CAN-bus compatible: 8.8V - 14.4V.
- Charging Amps: 1.25A (constant current)
- Indoor / Outdoor (lowest temperature: -40°F / -40°C)
- Save: Low Volt Start of 0.5V + 2-step* desulphation recovery (*1-step low volt pulse save during CAN-bus mode)
- For 4 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed)
- Weatherproof case with wall mounts
- Incl. 6ft. / 180cm AC supply lead and 6ft. / 180cm charge lead ending in SAE connector. Weatherproof battery lead, battery clip set & hanging hook
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected.

Tecmate, OptiMATE 4 Quad Program 12V battery charger

#993458

Stock:Yes

With EU wall plug. 7-step, 2-bank 12V 0.8A battery charger-tester-maintainer for 2 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah. Recovers sulphated batteries and then tests after charging. Maintains 2 batteries independently from each other. The automatic maintenance program provides what the battery needs, never overcharges, never undercharges.
- Charging Amps: 0.8A (constant current, per bank)
- Indoor / Outdoor (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 2V + 2 step desulphation recovery
- For 2 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 2 x 6ft / 180cm charge lead ending in SAE connector. 2 x Weatherproof battery lead & 2 x standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE 3 x 2 12V battery charger

#941201

Stock:Yes

With EU wall plug. 7-step, 12V 0.8A battery charger-tester-maintainer for Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah. Recovers sulphated batteries and then tests after charging. The automatic maintenance program provides what the battery needs, never overcharges, never undercharges.
- Charging Amps: 0.8A (constant current)
- Indoor / Outdoor (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 2V + 2 step desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector. 4Weatherproof battery lead & standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE 3 12V battery charger

#941200

Stock:Yes

With EU wall plug. 7-step, 4-bank 12V 0.8A battery charger-tester-maintainer for 4 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah. Recovers sulphated batteries and then tests after charging. Maintains 4 batteries independently from eachother. The automatic maintenance program provides what the battery needs, never overcharges, never undercharges.
- Charging Amps: 0.8A (constant current, per bank)
- Indoor / Outdoor (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 2V + 2 step desulphation recovery
- For 4 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah
- Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed
- Weatherproof case with wall mounts
- Incl. 6ft / 180cm AC supply lead and 4 x 6ft / 180cm charge lead ending in SAE connector. 4 x Weatherproof battery lead & 4 x standard battery clip set included
- No risk of overcharging
- Sparks suppressed
- Safe for vehicle electronics
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, 3 x 4-bank 12V battery charger

#941202

Stock:Yes