20 of 169 search results

SORT ON:

Universal basic wiring harness for custom use. Includes an on/off ignition switch, a hi/low toggle switch, fused circuits and wire ends. It will get a basic chopper up & running with wiring for electric start, headlamp & taillight. No turn signals or indicator light provisions. Complete with a detailed wiring schematic. Note: See 968177 for on/off replacement ignition switch as supplied with this kit
Cycle Visions

Cycle Visions, chopper wiring harness kit

#968176

Stock:Yes

This 6-8 pin plug adapter is required to allow installation of 'The Flasher' 968344 on 04-13 XL models. Note: Not compatible with Kuryakyn Panacea taillights. Note: When LED turn signals are used, a turn signal load equalizer, like MCS 968144 (with factory alarm) or 968145 (without factory alarm), is required.
Cycle Visions

Cycle Visions, 6-8 pin plug adapter for The Flasher

#968343

Stock:Yes

Plug-in module for rear side that adds a rapid three time 'flash' when braking, and a run-turn-brake function to single filament OEM and halogen lights. If you do not want the flashing brake function, it can be turned off by unplugging the connector marked 'flashing'. Note: A load equalizer is not required. Note: Not compatible with Kuryakyn Panacea taillights. Note: For 04-13 XL see 968343 adapter, which allows installation of 968344 'The Flasher' on these non CAN-bus Sportster models.
Cycle Visions

Cycle Visions, The Flasher plug-in module

#968344

Stock:Yes

Chrome plated aluminum. Covers the 3 nasty holes when the stock licenseplate bracket, above the taillight, is removed for a custom license plate set-up.
Cycle Visions

Cycle Visions Pyramid cover chrome

#968131

Stock:Yes

4mm thick neoprene cover. Used to prevent paintjob damage when working on your own or customer bikes. Made of 4mm thick neoprene, the same material as a wet suit, to protect paint, aluminum and chrome when working on the bike or during storage. Cycleskins™ covers are form fitted.
Cycle Visions

Cycle Visions Cycleskyns™ 3.2 gallon Sportster tank cover

#967001

Stock:Yes

4mm thick neoprene cover. With pockets. Used to prevent paintjob damage when working on your own or customer bikes. Made of 4mm thick neoprene, the same material as a wet suit, to protect paint, aluminum and chrome when working on the bike or during storage. Cycleskins™ covers are form fitted.
Cycle Visions

Cycle Visions Cycleskyns™ 3.2 gallon Sportster tank cover

#967003

Stock:Yes

Black powder coated. 18" tall. Side plate width 11". Made from 9/16" round steel bar. Can be used with stock or aftermarket side plates. Note: Cycle Visions advises these round 9/16" (14.3mm) 'Old School' sissy bars are not designed and not to be used to hold passengers. Note: Side plates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Old School Stick sissy bar 18" black

#968269

Stock:Yes

With detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968006

Stock:No

Without detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968003

Stock:Yes

No exhaust cut-out. Extended stretched saddlebag, used as a direct replacement for Touring hard bags. Saddlebag is fiberglass gel coated bottom ends only, it will take stock H-D lids and hardware.
Cycle Visions

Cycle Visions extended saddlebag, right side

#968220

Stock:Yes

Classic styling in black powder coated finish, 18" tall. Made from 9/16" square steel bar. Can be used with stock or aftermarket side plates. Side plate width 6.88" to 7.625" wide. Note: Side plates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Daggertude stick sissy bar 18", black

#968250

Stock:Yes

With detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968001

Stock:Yes

Without detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968009

Stock:Yes

Chrome. 18" tall. Side plate width 6.88" to 7.625" wide. Made from 9/16" square steel bar. Can be used with stock or aftermarket side plates. Note: Sideplates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Daggertude stick sissy bar 18", chrome

#968249

Stock:Yes

No exhaust cut-out. Extended stretched saddlebag, used as a direct replacement for Touring hard bags. Saddlebag is fiberglass gel coated bottom ends only, it will take stock H-D lids and hardware.
Cycle Visions

Cycle Visions extended saddlebag, left side

#968219

Stock:Yes

Black powder coated. 18" tall. Side plate width 8.25" to 8.75" wide. Made from 9/16" square steel bar. Can be used with stock or aftermarket side plates. Note: Side plates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Daggertude stick sissy bar 18", black

#968246

Stock:Yes

Without detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968000

Stock:Yes

Classic styling in black powder coated finish, 30" tall. Made from 9/16" square steel bar. Can be used with stock or aftermarket side plates. Side plate width 6.88" to 7.625" wide. Note: Side plates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Daggertude stick sissy bar 30", black

#968248

Stock:Yes

Without detachable sissy bar. Remove your saddlebag in 3 seconds. Used with stock saddlebags and can be used with or without docking hardware for sissy bars. Constructed from 303 stainless steel.
Cycle Visions

Cycle Visions, barebacks saddlebag mount kit

#968005

Stock:Yes

Chrome. 18" tall. Side plate width 8.25" to 8.75" wide. Made from 9/16" square steel bar. Can be used with stock or aftermarket side plates. Note: Sideplates not included. Note: Will not fit 'Plug-N-Play®' side plates.
Cycle Visions

Cycle Visions Twisted Stick sissy bar 18", chrome

#968334

Stock:Yes