Motorcycle Storehouse

Select your bike

BIKE SELECTOR

20 of 90 search results

Sort on:

Sort on:

Bumper 10. Fits XS 0.8 chargers (906041 and 906042). This is a protective silicone rubber bumper that fits snugly around the charger body and offers additional grip and damage protection.

CTEK, BUMPER10 protective charger bumper for 0.8A chargers

#906059

Stock:Yes

MXS charger wall mount. Allows you to store the MSX charger and also stores the clamp-on charge cables, when not in use. Fits all MXS chargers, both 3.8A (906046 / 906047) and 5A (906048 / 906049) models. The open frame design allows easy access to charger functions.

CTEK, MXS 3.8A and 5.0A battery charger mounting bracket

#906057

Stock:Yes

Monitor cable for Lithium batteries. 60cm long. With M6 / 1/4" ringlets to 2-pin SAE connector with waterproof sealing cap.
- Micro processor driven 4 LED system used to monitor battery status.
- Informs you if the battery is in a good/needs charge/not good condition
- When the engine is running it also informs you if the vehicle's charging system is working. Then the LED mode changes to an arrow, with the pointer reaching the LED matching the voltage being delivered by charging system. No arrow means there is no charge
- A bright red LED warns that the charge level has reached 50% and that it is time to recharge that battery
- During vehicle storage the LED matching the battery’s state of charge will blink every 5 seconds, drawing very little power (0.2 milli-amps) to do so, in fact 20-100 times less than the vehicle’s circuitry is drawing from the battery at the same time
- Fast blink mode for first 15 seconds after connection to battery, for quick check of multiple batteries (e.g. vehicles on showroom floor)

Tecmate OptiMATE Monitor O-127 cable. Lithium

#941815

Stock:Yes

CT5 charger wall mount. Allows you to store the CT5 charger and also stores the clamp-on charge cables, when not in use. Fits CT5 chargers (906043 and 906044). The open frame design allows easy access to charger functions.

CTEK, CT5 battery charger mounting bracket

#906058

Stock:Yes

With EU wall plug. Professional 4-bank battery saving charger for power sport & small engine 12V batteries. No further battery knowledge required. Connect up to 4 x 12V batteries and let the charger do the rest.
- OEM recommended battery care center for correct activation of new batteries and recovery, charge and testing of neglected sulphated / low-voltage batteries.
- New mode: a 1 hour activation charge only for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ‘dry-charged’ batteries that are delivered with a separate custom acid pack
- Charging Amps: 4A maximum, Ampmatic control. (2A max. when 2A is selected)
- Use: Indoor / workshop environment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 1.8V + 2 step desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 2 – 40Ah
- Selectable 110-120V / 220-240V 50-60Hz
- Vented industrial table top case.
- Incl. 6ft / 180cm AC supply lead and 4 x 6ft / 180cm charge lead ending in SAE connector. 4 x standard battery clip sets
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, Pro 4 battery charger. 12V

#941416

Stock:Yes

UK wall plug. 12V 0.8A. For up to 10Ah batteries. Selectable Lithium or flooded, sealed, maintenance free, AGM and lead acid batteries. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved. Dimensions 8.3cm x 5cm x 3.5cm.

Battery Tender, Junior 800 - selectable (UK)

#905503

Stock:No

UK wall plug. 1.25A. Selectable 6/12V. Selectable Lithium or flooded, sealed, maintenance free, AGM and lead acid batteries. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved. Dimensions 17.2cm x 9.3cm x 4.9cm.

Battery Tender, selectable charger. Lithium & 12/6V

#905506

Stock:No

With EU wall plug. 4-step 6V/12V ChargeMatic Battery charger-maintainer. Will charge any 6V or 12V lead-acid battery, both starter and deep cycle. Temperature protected charger with IUoU 4-step charging program, including reversion from 'maintenance' float stage if high current is drawn during storage charging. Simply select 6 or 12 voltage, hook up the battery and this temperature compensated, 4-step charger will do the rest.
- Charging Amps: 1.2A (temperature protected)
- 4-step. Bulk, Absorption, maintain & revert
- Indoor (lowest temperature: -4°F / -20°C)
- Low Volt Start of 2V for 6 or 12V batteries
- For 6V & 12V Lead Acid, AGM, GEL lead-acid batteries, starter and deep cycle, up to 50Ah
- EU 220-240V 50-60Hz North America: 110-120V 50-60Hz.
- Standard case (vented)
- Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector, a fused battery lead & standard battery clip set
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, AccuMate 6/12 1.2A battery charger

#941412

Stock:No

CTEK’s charger BUMPER for CT5 Powersport chargers. This is a protective silicone rubber bumper that fits snugly around the charger body and offers additional grip and damage protection.

CTEK, CT5 protective charger bumper

#906063

Stock:Yes

UK wall plug. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. Water resistant and shock/vibration resistant with a weight less than 2kg. A compact and sturdy charger, ready for portable operations or permanent mounting in a garage etc. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved.

Battery Tender, Power Tender 12V@5A High Efficiency

#501303

Stock:No

UK wall plug. 2 bank charger 12V. Allows charging / maintaining 1 or 2 batteries at once. Dimensions: 11.5cm wide x 8.5cm high x 17.5cm deep.Microprocessor controlled, 100-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. CE approved.
Note: When using multi-bank chargers, with the batteries in the bikes, you can order 990048 quick-disconnect cable which offers 25 foot (7.5 meters) of convenience.

Battery Tender, International Plus - 1.25A charger

#990078

Stock:Yes

With UK wall plug. Will charge 12V & 6V lead-acid, AGM and Lithium LiFePO4 batteries. Selectable 1A or 4A charging. With digital screen. Can be used as trickle charger.
- Specific AGM mode for sealed batteries
- Digital screen with live voltage reading
- Hook attachment
- Suitable for 6V and 12V batteries
- 1A and 4A selectable charge
- Clear split between Lithium and lead-acid charging modes and algorithms
- Battery Recovery for deeply discharged batteries
- Battery health check after charging
- Maintaining mode, with 4 hour intervals voltage checks
- Protected against reverse polarity, overcharging, overcurrent, overheating and short-circuits
- User friendly detection for reverse polarity, low-voltage or damaged batteries
- IP 65 splash and dust proof for outdoor use
- Adjusts for varying A/C line voltage and delivers consistent charging current
- 8 step lead acid charging
- 7-step Lithium charging
- Input: 220-240V AC 50-60Hz
- Output: 6V or 12V 1A or 4A DC
- Dimensions: 210 x 87 x 50mm
- Weight: 0.6 kg
- IP rating: IP 65
- Battery: 4-80 Ah > Charge, 4 - 120 Ah > Maintenance

Shido, dual battery charger 12V/6V DC 4.0 (UK)

#932960

Stock:Yes

UK wall plug. 0.8A / 3.8A 12V charger. For 1.2Ah-85Ah lead-acid (AGM, GEL, EFB, MF, CaCa) batteries. With a mode button to switch between charging bike (0.8A) and car (3.8A) batteries. Offers a fully automated 7 step charge and maintenance sequence. Features include battery diagnosis to establish whether your battery can receive and retain a charge, a patented desulphation program and a 'Snowflake' program for charging on cold days. With CTEK's patented float/pulse system, which is the most efficient maintenance mode when a battery is connected for long periods. Simple to use and you can follow the whole charging process on the clear, easy to read display.
- 12 volts.
- 0.8A (bike) and 3.8A (car) modes.
- Lead-acid batteries.
-AGM mode.
- 7 steps.
- Clamps.
- Eyelet connector.
- Safe spark free operation.
- Reverse polarity protected.
- Splash and dust proof (IP65).

CTEK, MXS 3.8 battery charger, UK

#906047

Stock:Yes

UK wall plug. 4.0A. Selectable 6/12V. Selectable Lithium or flooded, sealed, maintenance free, AGM and lead acid batteries. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved. Dimensions 17.2cm x 9.3cm x 4.9cm.

Battery Tender, selectable charger. Lithium & 12/6V

#905508

Stock:No

With EU wall plug. The power sport OEM recommended load tester, power desulphator and charger for all types of 12V lead-acid batteries. The BatteryMate has been saving batteries for 25 years!
- New battery activation – 30 minute activation charge for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ‘dry-charged’ batteries that are delivered with a separate custom acid pack
- True load tester selectable from 15A to 150A – Automatically tests battery cranking amps up to 330CCA. 3 second test simulates normal engine cranking / start, 15 second test checks battery health
- Powersport specific charging algorithm – 4 step charging method recovers any 12V battery. MF mode allows up to 16.9V for ‘dry-charged’ AGM batteries
- Temperature regulated charging – Charge voltage is adjusted according to ambient temperature. (-4mV/°C/cell above/below 68°F/20°C)
- Accurate voltage sensing. Charge leads have integrated voltage sense wires for exact voltage measurement at the battery
- Easy to use. 6 position combination selector allows selection of correct test and charge current for connected battery. TEST and then select max. charge time according to result, press 'charge' button. Program completes charging automatically and then tests the battery
- Charging Amps: 9A maximum; 1, 2, 3, 5, 7, 9 Amp selection
- Testing Amps: 150A maximum; 15, 35, 50, 70, 100, 150 Amp selection
- Indoor / workshop environment (lowest temperature: -4°F / -20°C)
- Save: Low Volt Start of 1V + high power desulphation recovery
- For Lead Acid, AGM & GEL 12V batteries from 2 – 40Ah
- Selectable 110-120VAC / 220-240VAC 50-60Hz
- On/Off power switch and replaceable fuse protection
- Vented industrial table top case
- Incl. 6ft / 180cm AC supply lead and 1 pair high current 6ft / 180cm charge leads ending in heavy duty battery clamps
- No risk of overcharging
- Sparks suppressed
- Safe for long-term battery maintenance
- Automatic shut-down if short-circuited or battery disconnected

Tecmate OptiMATE, BatteryMate 150/9 battery charger

#941415

Stock:Yes

Will charge 12V & 24V lead-acid, AGM and Lithium LiFePO4 batteries. Designed to auto-detect each battery type and will select correct 5-12.5 (for 24V batteries) and 5-12.5-25A (for 12V batteries) charge cycles to maximize battery life. Can be used as trickle charger. Complete with integrated power supply enabling a no-data loss battery change. Lithium batteries are equipped with a BMS that in some cases can prevent the start of the charging cycle, the 'forced charge' UVP (Under Voltage Protection) unlock function is used to unlock these Lithium batteries. Compatible with motorcycle up to truck batteries.
- Backlit digital graphic display
- Power supply voltage 220-240V
- Reverse polarity protection
- Spark protection
- Recovery function for flat batteries
- Frequency 50-60Hz
- Rated current (min-max) 5-12.5-25Ah for 12V batteries
- Rated current (min-max) 5-12.5Ah for 24V batteries
- Charging and testing stages 9
- Battery voltage 12V - 24V
- Charge capacity 5Ah ÷ 550Ah
- Maintenance capacity 5Ah ÷ 800Ah
- Memory saving feature 13.8V
- IP20 splash and dust proof for indoor use
- Size 260 x 130 x 75mm
- Weight 2.5 Kg

Shido, multi battery charger 12V/24V DC 25.0 (EU)

#932958

Stock:Yes

With UK wall plug. Will charge 12V lead-acid, AGM and Lithium LiFePO4 batteries with a 1.0A charge. Can be used as trickle charger.
- Clear split between Lithium and lead-acid charging modes and algorithms
- Battery Recovery for deeply discharged batteries
- Battery health check after charging
- Maintaining mode, with 4 hour intervals voltage checks
- Protected against reverse polarity, overcharging, overcurrent, overheating and short-circuit
- User friendly detection for reverse polarity, low-voltage or damaged batteries
- IP 65 splash and dust proof for outdoor use
- Adjusts for varying A/C line voltage and delivers consistent charging current
- 8 step lead acid charging
- 7-step Lithium charging
- Input: 220-240V AC 50-60Hz
- Output: 12V 1A DC
- Dimensions: 180 x 80 x 40mm
- Weight: 0.4 kg
- IP rating: IP 65
- Battery: 2-40 Ah > Charge, 2 - 100 Ah > Maintenance

Shido, dual battery charger 12V DC 1.0. (UK)

#932957

Stock:Yes

8A 12V charger. For 3Ah to 180Ah lead-acid (AGM, GEL, EFB, MF, CaCa) and lithium batteries. The CS ONE has APTO™ (Adaptive Charging) technology to recognise the type of battery you want to charge and tells how long it will need to charge it. There are no buttons on the CS ONE, just connect any lead-acid or lithium battery and simply charge. Polarity free clamps mean you don’t even need to worry
about which clamp goes where, so you’ll never make a wrong connection again. The clamps are spark free too, so don’t worry if you accidentally touch them together Unlock additional features using the Bluetooth® enabled CTEK App. Select ‘RECOND’ to restore and recondition your battery. Choose ‘WAKE UP’ for lithium batteries with under voltage protection or to bring deeply discharged lead-acid batteries back to life. Select ‘SUPPLY’ to turn the CS ONE into a useful 12 V supply

CTEK, CS ONE Battery charger. UK wall plug

#954369

Stock:Yes

With UK wall plug. 2.3A 12V charger. For 5Ah to 25Ah batteries. Auto-selects lead acid, AGM and Lithium (LiFePO4, Li-Fe, Li-iron, LFP) batteries. Offers three fully automatic charging and maintenance programs with a fully automated 6 step charge sequence. A special reconditioning (Recond) mode is used for helping to save deeply discharged lead-acid batteries.
- 12V.
- 2.3 Amps.
- Lead Acid batteries.
- AGM batteries.
- Lithium mode.
- Reconditioning mode.
- 6 steps.
- Clamps.
- Eyelet connector.
- Splash and dust proof (IP65).
- Safe spark free operation.
- Reverse polarity protected.
- Short circuit proof.

CTEK, CT5 Powersport battery charger, UK

#906044

Stock:Yes

8A 12V charger. For 3Ah to 180Ah lead-acid (AGM, GEL, EFB, MF, CaCa) and lithium batteries. The CS ONE has APTO™ (Adaptive Charging) technology to recognise the type of battery you want to charge and tells how long it will need to charge it. There are no buttons on the CS ONE, just connect any lead-acid or lithium battery and simply charge. Polarity free clamps mean you don’t even need to worry
about which clamp goes where, so you’ll never make a wrong connection again. The clamps are spark free too, so don’t worry if you accidentally touch them together Unlock additional features using the Bluetooth® enabled CTEK App. Select ‘RECOND’ to restore and recondition your battery. Choose ‘WAKE UP’ for lithium batteries with under voltage protection or to bring deeply discharged lead-acid batteries back to life. Select ‘SUPPLY’ to turn the CS ONE into a useful 12 V supply

CTEK, CS ONE Battery charger. EU wall plug

#954368

Stock:Yes