20 of 183 search results

SORT ON:

M8 threaded on both ends (M8 inside to M8 outside threads). Used to extend the mounting distance with 30mm for any small 8mm turn signal. Used for required distance between right & left side turn signal for better visibility and added safety. - M8 threaded - 30mm extension - 13mm outside diameter - CNC machined aluminum - Sold in pairs
Daytona
New

Daytona, 8mm turn signal extension set. Black

#993658

Stock:Yes

Koso
Discontinued

Koso, turn signal adpating wire for HD

#701744

Stock:Yes

Chrome plated. Used when you want to remove the front turn signals on your fork slider equipped H-D. Lets you remove the OEM turn signal bracket & hide the ugly holes. CNC machined from billet aluminum.
Covingtons

Covingtons, turn signal eliminators. Chrome

#953907

Stock:Yes

Black diamond cut finish. Used when you want to remove the front turn signals on your fork slider equipped H-D. Lets you remove the OEM turn signal bracket & hide the ugly holes. CNC machined from billet aluminum.
Covingtons

Covingtons, turn signal eliminators. Black diamond

#953908

Stock:Yes

FL style rear turn signal bracket of 8-7/8" wide. Stock length. OEM replacement reference 68526-63.
MCS

Rear turn signal bar, FL style 8-7/8" wide. Polished

#910178

Stock:Yes

I.D is .415" (10.54mm), O.D. is .685" (17.40mm)
Chris Products

Chris, turn signal spacers 1" (25.4mm) long. Chrome

#932082

Stock:Yes

I.D is .415" (10.54mm), O.D. is .685" (17.40mm). Includes 5 pieces of chrome plated turn signal spacers. Includes following lengths: -1x 1/4" (6.4mm) long - 1x 1/2" (12.7mm) long - 1x 3/4" (19mm) long - 1x 1" (25.4mm) long - 1x 1-1/4" (31.8mm) long
Chris Products

Chris, turn signal spacer kit. Chrome

#932084

Stock:Yes

8-1/4" (21cm) wide. Extra narrow. Up to almost 5" (12.7cm) less wide, depending on model, when compared to the stock length of the stock FL style turn signal brackets. OEM replacement reference 91778-85.
MCS

FL style rear turn signal bar. Chrome. short

#930655

Stock:Yes

I.D is .415" (10.54mm), O.D. is .685" (17.40mm)
Chris Products

Chris, turn signal spacers 3/4" (19mm) long. Chrome

#932081

Stock:Yes

Used to mount stock or custom turn signals directly on the front fork instead of the handlebars. Includes hardware.
MCS

Front springer turn signal relocation kit. Chrome

#900262

Stock:No

Steel relocation studs, that replace the stock pinch bolts in the upper or lower triple tree. Allows you to move the turn signals from the handlebars to the fork. 5/16-24 to 10mm-1.5 threaded.
MCS

FX, Dyna front turn signal relocation kit. Chrome

#900434

Stock:Yes

Front. Turn signal mount kit for left & right side. OEM replacement reference 68477-73.
Chris Products

Chris Products, turn signal mount kit. Front. L/R. Chrome

#932067

Stock:Yes

- Comes in sets of two black heat treated T6 aluminum mounting brackets - Can be used with a variety of turn signals - Brackets install low on the frame, close to the lower front of the engine, for that custom look - Center to center mounting holes 86mm, overall length 105mm - Overall length 72mm - Diameter mounting holes 12.5mm and 9.75mm Note: Turn signals are not included. Note: See 914034 for rear brackets.
MCS

XL Sportster turn signal mount brackets. Front. Black

#914033

Stock:Yes

Lets you mount FL style turn signals just about anywhere. - Chrome plated steel - Straight mount brackets. OEM replacement reference 68527-63.
MCS

FL turn signal bracket set. Chrome

#940644

Stock:Yes

For 517453 saddlebag support kit
MCS

Turn signal relocation kit

#517454

Stock:No

Black anodized. Clamps around the fork tubes to allow installation of M10x1.25 or M10x1.50 threaded turn signals. The hinged design folds open for easy installation and fork disassembly is not required. Clamps are CNC machined from billet 6061-T6 aluminum with a special machined billet nut that slides over the threads. Comes with two M10x1.25 nuts and two M10x1.50 nuts for installing the stem of the turn signal.
Motone

Motone, Wrap-around turn signal brackets, 47mm forks

#905817

Stock:Yes

Polished finish. Clamps around the fork tubes to allow installation of M10x1.25 or M10x1.50 threaded turn signals. The hinged design folds open for easy installation and fork disassembly is not required. Clamps are CNC machined from billet 6061-T6 aluminum with a special machined billet nut that slides over the threads. Comes with two M10x1.25 nuts and two M10x1.50 nuts for installing the stem of the turn signal.
Motone

Motone, Wrap-around turn signal brackets, 35mm forks

#905808

Stock:Yes

Used to move the turn signals to the frame down-tubes, below the fuel tank. Bracket tube is hollow to route wiring and 8mm threaded for use with all custom turn signals that have 8mm threads. Complete with installation hardware. Gloss black powder coated steel. Note: Not compatible with engine guards.
Westland Customs

Westland Customs, front turn signal bracket 22cm. Black

#941551

Stock:No

Used when installing aftermarket turn signals.
Koso

KOSO, turn signal wire adapter. Triumph

#942311

Stock:Yes

Used when installing aftermarket turn signals.
Koso

KOSO, turn signal wire adapter. Suzuki

#942312

Stock:Yes