20 of 50 search results

SORT ON:

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 19mm

#580882

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 13.8mm

#580884

Stock:Yes

Universal gear puller with 2/3 adjustable jaws, 5 1/2" reach, 7" spread. Weight 879 gram. Note: The USA 'Ton' is a non-metric unit of measurement and approximately 508kg.
Lisle

2 or 3 jaw rev & adj 5 ton puller (2540kg)

#530856

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 21mm

#580881

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 17mm

#580883

Stock:Yes

150mm long. Set of 2 extensions. Weight 0.805kg - Used to extend the reach of the quick adjusting jaws. - The extensions are interconnectible. Each jaw extension added is an additional 150mm reach. - Fits all of our 20 and 30 build series Kukko gear pullers equipped with the 'Quick Adjusting arms'.
Kukko

Kukko, 2 jaws extensions for 'Quick Adjusting jaw' pullers

#950995

Stock:Yes

150mm long. Set of 3 extensions. Weight 1.205kg - Used to extend the reach of the quick adjusting jaws. - The extensions are interconnectible. Each jaw extension added is an additional 150mm reach. - Fits all of our 20 and 30 build series Kukko gear pullers equipped with the 'Quick Adjusting arms'.
Kukko

Kukko, 3 jaws extensions for 'Quick Adjusting jaw' pullers

#950996

Stock:Yes

With swiveling jaws. Designed for wide variety pulling jobs. - Number Of Jaws: 3 - Build Series: 42 - Spread (in mm): 12-65 - Depth (in mm): 64 - Maximum Load: 1500kg - Space Below (in mm): 4 - Space Next To It (in mm): 15 - Weight: 295 grams
Kukko

Kukko, universal swiveling jaw gear puller. 3 arms

#951010

Stock:Yes

With a special clamp to hold the arms tight to prevent 'slip-off'. Designed for a wide variety of pulling jobs with tight or difficult access. - Number Of Jaws: 2 - Build Series: 240-0 - Spread (in mm): 25-50 - Depth (in mm): 70 - Maximum Load: 1000kg - Space Below (in mm): 2.6 - Space Next To It (in mm): 20 - Weight: 0.690kg - Remarks: With clamp
Kukko

Kukko, 'Cobra' puller with side clamp. 2 arms

#951018

Stock:Yes

Inner ball bearing puller used to pull bearings on the inside diameter or pull outer bearing races only. Used with 951034 slide-hammer device and 951036 counterstay support puller. - Inside diameter ball bearing in mm: 6-10 - Effective depth in mm: 14 - Internal extractor length in mm: 73 - Number of segments: 2 - Weight: 0.120kg - Pulls ISO bearings: 626; 607; 627; 608; 619/8; 628/8; 609; 618/9; 629; 6000; 6200; 6300; 6800; 6900; 61800; 61900; 62200; 62300. Note: The 951064 slide hammer and 951036 counterstay are not included. These must be purchased separately.
Kukko

Kukko, internal ball bearing extractor. 6-10mm ID

#951025

Stock:Yes

For use with Kukko internal ball bearing extractors. - Reach: 165mm - Support Surface: 14mm x 18mm - Max load: 4000kg - Weight: 1.873kg. Note: The 951034/951035 slide hammers and 951036/951037 counterstay support pullers are not included with the ball bearing extractors and must be purchased separately.
Kukko

Kukko, Counterstay / Counter support. 4000kg

#951037

Stock:Yes

With swiveling jaws. Designed for wide variety pulling jobs. - Number Of Jaws: 2 - Build Series: 41 - Spread (in mm): 12-65 - Depth (in mm): 65 - Maximum Load: 1000kg - Space Below (in mm): 4 - Space Next To It (in mm): 15 - Weight: 220 grams
Kukko

Kukko, universal swiveling jaw gear puller. 2 arms

#951009

Stock:Yes

For use with Kukko internal ball bearing extractors. - Overall length: 290mm - Mass of impact: 0.5kg - Slide impact length: 200mm - Rod connection thread: M12 - Internal thread: M12/M10 - Threaded adapters: AG: M10, IG: M7 - Weight: 0.745kg Note: The 951034/951035 slide hammers and 951036/951037 counterstay support pullers are not included with the ball bearing extractors and must be purchased separately.
Kukko

Kukko, slide hammer 290mm OAL

#951034

Stock:Yes

Used with hand tools to externally pull ball bearings, roller bearings and inner races from a shaft where the bearing is installed tightly to another surface, so there is not enough room to use regular pulling jaws. When tightened, the bearing separator will pinch-in between the bearing and the surface making it possible to pull the bearing from the shaft. The required puller, that actually pulls the separator to remove the bearing, is sold separately and available as 951057. - Build Series: 15 - Diameter of Shaft (in mm): 12-75 - Side Screw Length (in mm): 75 - Weight: 1.105kg - Space Below (in mm): 0 - Space Next To It (in mm): 75 - Spread (in mm): 12-75 - Depth (in mm): 200 Note: 951039 bearing separator will require the use of 951057 puller. Separator and puller are sold separately.
Kukko

Kukko, bearing separator. 12-75mm

#951039

Stock:Yes

- Build Series: 18 - Side Screw Length (in mm): 60-150 - Side Screw Depth (in mm): 122-200 - Thread: M10 - Hex Drive (Male) (in mm): 19 - Maximum Load: 5000kg - Maximum Torque: 70Nm - Weight: 2.050kg
Kukko

Kukko, puller for 951039 bearing separator

#951057

Stock:Yes

Inner ball bearing puller used to pull bearings on the inside diameter or pull outer bearing races only. Used with 951034 slide-hammer device and 951036 counterstay support puller. - Inside diameter ball bearing in mm: 8-12 - Effective depth in mm: 14 - Internal extractor length in mm: 73 - Number of segments: 2 - Weight: 0.115kg - Pulls ISO bearings: 608; 619/8; 628/8; 609; 618/9; 629; 6000; 6200; 6300; 6800; 6900; 61800; 61900; 62200; 62300; 6001; 6201; 6301; 6801; 6901; 16001; 16101; 61801; 61901; 62201; 62301. Note: The 951064 slide hammer and 951036 counterstay are not included. These must be purchased separately.
Kukko

Kukko, internal ball bearing extractor. 8-12mm ID

#951026

Stock:Yes

Inner ball bearing puller used to pull bearings on the inside diameter or pull outer bearing races only. Used with 951034 slide-hammer device and 951036 counterstay support puller. - Inside diameter ball bearing in mm: 10-14 - Effective depth in mm: 14 - Internal extractor length in mm: 73 - Number of segments: 2 - Weight: 0.115kg - Pulls ISO bearings: 6000; 6200; 6300; 6800; 6900; 61800; 61900; 62200; 62300; 6001; 6201; 6301; 6801; 6901; 16001; 16101; 61801; 61901; 62201; 6230. Note: The 951064 slide hammer and 951036 counterstay are not included. These must be purchased separately.
Kukko

Kukko, internal ball bearing extractor. 10-14mm ID

#951027

Stock:Yes

Inner ball bearing puller used to pull bearings on the inside diameter or pull outer bearing races only. Used with 951034 slide-hammer device and 951036 counterstay support puller. - Inside diameter ball bearing in mm: 12-16 - Effective depth in mm: 25 - Internal extractor length in mm: 72 - Number of segments: 2 - Weight: 0.110kg - Pulls ISO bearings: 6001; 6201; 6301; 6801; 6901; 16001; 16101; 61801; 61901; 62201; 62301; 6002; 6202; 6302; 6802; 6902; 16002; 61802; 61902. Note: The 951064 slide hammer and 951036 counterstay are not included. These must be purchased separately.
Kukko

Kukko, internal ball bearing extractor. 12-16mm ID

#951028

Stock:Yes

- Used to pull 12mm to 70mm ID ball bearings, bearing outer races and bushings - With free-moving, self-retaining jaws with internal spring washer - The built-in thrust bearing offers reduced friction - Complete with a sturdy carrying case - Tool set weight: 9.94kg - Set includes: - 22-1 Counterstay (55mm counter support spread, 120mm reach) - 22-2 Counterstay (100mm counter support spread, 165mm reach) - 21-1 Internal extractor (5-8mm) - 21-2 Internal extractor (14-19mm) - 21-3 Internal extractor (18-23mm) - 21-4 Internal extractor (20-30mm) - 21-5 Internal extractor (28-40mm) - 21-6 Internal extractor (35-46mm) - 21-7 Internal extractor (45-58mm) - 21-8 Internal extractor (56-70mm). Note: This set is compatible with Kukko's slide hammer (MCS 951034), which must be purchased separately when required.
Kukko

Kukko, ball bearing inner puller set

#951033

Stock:Yes

Universal gear puller. Supplied with 3 jaws and can be used as a 2 or 3 jaw puller. Jaws grip tighter as more pressure is applied and are reversible. Made drop forged steel alloy with a Rockwell hardness of 45 Hrc. - Size: 3" - Spread: 4" - Reach: 2.5" - Max load: 2000kg - Weight: 604 grams - Height: 80mm - Length: 127.8mm - Width: 93.6mm - Number of jaws used: 2 to 3 - Jaws grip tighter as more pressure is applied - Reversible jaws - Material: Drop forged steel alloy - Hardness: 45 Rockwell (Hrc)
Sonic

Sonic, 2-3 Jaw 3" reversible puller

#954076

Stock:Yes