20 of 164 search results

SORT ON:

9 step 12V / 12.8V 1.25A sealed battery saving charger & maintainer for AGM, GEL & STD 12V batteries from 4 – 60Ah & Lithium (LiFePO4) 12.8/13.2V batteries from 2 – 15Ah. OptiMate 4 Quad Program tests before & after charging and can recover a ‘dead-flat’ lead-acid & lithium (LiFePO4) battery from as low as 0.5 Volts. - Selectable, 4 charge programs: 1).12V Smart desulphation: 0.5V - 14.4V. 2). BMW CAN-bus compatible: 5V - 14.4V. 3). 12.8V Low Volt Recovery: 0.5V - 14.4V. 4). BMW CAN-bus compatible: 8.8V - 14.4V. - Charging Amps: 1.25A (constant current) - Indoor / Outdoor (lowest temperature: -40°F / -40°C) - Save: Low Volt Start of 0.5V + 2-step* desulphation recovery (*1-step low volt pulse save during CAN-bus mode) - For 4 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah - Input: Global (100-240V 50-60Hz), high efficiency (CEC listed) - Weatherproof case with wall mounts - Incl. 6ft. / 180cm AC supply lead and 6ft. / 180cm charge lead ending in SAE connector. Weatherproof battery lead, battery clip set & hanging hook - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected.
Optimate
New

Tecmate, OptiMATE 4 Quad Program 12V battery charger

#993458

Stock:Yes

MCS Scan, connector cable
MCS
New

MCS Scan, connector cable

#700800

Stock:Yes

Bronze. 5-step 12V / 12.8V 2A sealed battery maintainer. For Lead Acid, AGM, GEL 12V batteries from 6 to 96Ah and 12.8/13.2V lithium (LiFePO4) batteries. It senses the battery condition, recharges and then keeps the battery 100% ready. The fully automatic maintenance program provides what the battery needs, never overcharges, never undercharges. - Charging Amps: 2A (constant current) - Charging volts: nominal: 12V & 12.8V range: 4V – 14.4V - Indoor / Outdoor (lowest temperature: -40°F / -20°C) - For Lead Acid, AGM & GEL 12V batteries from 3 – 96Ah - Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed - Weatherproof case with wall mounts - Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector - weatherproof battery lead & battery clip set - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term 24-7 battery maintenance - Automatic shut-down if short-circuited or battery disconnected
Optimate
New

Tecmate, Optimate, 2 Duo 12V battery charger. Bronze

#998339

Stock:Yes

9-step 12V / 12.8V 1.25A sealed battery saving charger & maintainer for AGM, GEL & STD 12V and works with 12.8V Li-Ion made batteries with LiFe & LFP technology. Note: Quad program – select program 1 or 3 to charge battery direct or through a live (hot) 12V socket, or program 2 or 4 to charge through BMW CAN-bus controlled 12V socket. Will require optional cable accessory to connect to socket. - Fully automatic and safe charger / trickle charger for 24-7 use - BMW CAN-bus compatible, automatic activation - Smart desulphation from 0.5V, for Pb (conventional lead acid) batteries - Low voltage recovery & BMS reset, for LFP battery - Tests battery state of health - Energy saving technology - Stand-by power less than 0.5W - Efficient 24-7 battery maintenance - Weatherproof - Rated for use down to -40°C / -40°F - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected - Includes weatherproof battery lead, battery clip set & hanging hook.
Optimate
New

Tecmate, OptiMate 4 Quad Program

#998313

Stock:Yes

UK wall plug. 2 bank charger 12V. Allows charging / maintaining 1 or 2 batteries at once. Dimensions: 11.5cm wide x 8.5cm high x 17.5cm deep.Microprocessor controlled, 100-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. CE approved. Note: When using multi-bank chargers, with the batteries in the bikes, you can order 990048 quick-disconnect cable which offers 25 foot (7.5 meters) of convenience.
Battery Tender

Battery Tender, International Plus - 1.25A charger

#990078

Stock:Yes

Used to test electrical connections. Retractable test lead pulls out, and stays at desired length. Includes insulated alligator clips. Rewinds in protective case when not in use. With 18 gauge (ø1.02mm / 0.82mm²) copper wire. With 30 feet single wire.
Lang Tools

Lang Tools, retractable electrical test lead, std housing

#514396

Stock:Yes

Used to crimp stamped Deutsch terminal pins of Deutsch DT and DTM series connectors only.
Namz

Namz, Deutsch ratcheting crimp tool

#548170

Stock:No

Fits 530807 circuit tester.
Lisle

Lisle, replacement bulb for circuit tester

#530740

Stock:Yes

Replacement for 530814 power / ground outlet, 530802 circuit tester and 530808 circuit tester, low side only.
Lisle

Lisle, replacement bulb

#530734

Stock:Yes

Up to 12V. Protects fingers and automatically centers wire. The little hook to grab a specific wire, and the pointed tip will actually pierce the wire to check for power. Great for confined spaces. With alligator ground clip. Note: See 530739 for replacement bulb.
Lisle

Lisle, Handy Hooker circuit tester

#530800

Stock:Yes

Replacement for 530804 Noid Light tool
Lisle

Lisle, replacement probe

#530735

Stock:Yes

Professional 8.5" (21.6cm) long crimping tool for primary wire insulated terminals. Adjustable tension and molded hand grips. Crimps 22 (0.33mm² / ø0.64mm) to 10 (5.3mm² / ø2.6mm) gauge wires.
Standard

Standard Co, ratcheting terminal crimp tool

#951705

Stock:Yes

Std duty booster cables. 12ft. (3.65m), 8 gauge (3.26 ø mm). Soft blend PVC outer jacket for use with -40° to +140°F (-40° to 60°C). Comes with alligator style clamps.
Standard

Standard Co, Battery jumper cables 400A

#951768

Stock:No

8" (20cm) long multi-functional crimping tool. Cuts wire, strips wire, crimps terminals. Special crimping nest for 7mm ignition wire terminals. Strips 22 gauge (0.33mm² / ø0.64mm) to 10 gauge (5.3mm² / ø2.6mm) wires.
Standard

Crimp 'n cut, wire tool

#951706

Stock:Yes

Standard duty booster cables. 12ft. (3.65m), 4 gauge (5.19 ø mm). Soft blend PVC outer jacket for use with -40° to +140°F (-40° to 60°C). Comes with alligator style clamps.
Standard

Standard Co, Battery jumper cables 400A

#951769

Stock:Yes

UK wall plug. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. Water resistant and shock/vibration resistant with a weight less than 2kg. A compact and sturdy charger, ready for portable operations or permanent mounting in a garage etc. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved.
Battery Tender

Battery Tender, Power Tender 12V@5A High Efficiency

#501303

Stock:No

Series 162 iS PH VDE Phillips insulated screwdriver. Allows working with live wiring up to 1000V, individually tested as per IEC 60900. With multi-component handle. Shaft is zinc-phosphated and had a reduced diameter, with integrated protective insulation, to allow better access to sunken screws and spring elements. Tip thickness at tip: PH1. Shaft length: 80mm. Handle length: 98mm.
Wera

Wera screwdriver VDE Insulated for Phillips screws

#580839

Stock:Yes

Series 165 iS PZ VDE Pozidriv insulated screwdriver. Allows working with live wiring up to 1000V, individually tested as per IEC 60900. With multi-component handle. Shaft is zinc-phosphated and had a reduced diameter, with integrated protective insulation, to allow better access to sunken screws and spring elements. Tip thickness at tip: PZ1. Shaft length: 80mm. Handle length: 98mm.
Wera

Wera screwdriver VDE Insulated for Pozidriv screws

#580841

Stock:Yes

Series 165 iS PZ VDE Pozidriv insulated screwdriver. Allows working with live wiring up to 1000V, individually tested as per IEC 60900. With multi-component handle. Shaft is zinc-phosphated and had a reduced diameter, with integrated protective insulation, to allow better access to sunken screws and spring elements. Tip thickness at tip: PZ2. Shaft length: 100mm. Handle length: 105mm.
Wera

Wera screwdriver VDE Insulated for Pozidriv screws

#580842

Stock:Yes

Series 190 i VDE Insulated screwdriver, actually a hexagon nut driver, for regular hex nuts and bolts. Allows working with live wiring up to 1000V, individually tested as per IEC 60900. With multi-component handle. Shaft is zinc-phosphated and had a reduced diameter, with integrated protective insulation. Nut size: 5.5mm. Shaft length: 125mm. Handle length: 98mm. Shaft diameter: 11mm.
Wera

Wera nutdriver VDE Insulated, Metric

#580843

Stock:Yes