20 of 92 search results

SORT ON:

9 step 12V / 12.8V 1.25A sealed battery saving charger & maintainer for AGM, GEL & STD 12V batteries from 4 – 60Ah & Lithium (LiFePO4) 12.8/13.2V batteries from 2 – 15Ah. OptiMate 4 Quad Program tests before & after charging and can recover a ‘dead-flat’ lead-acid & lithium (LiFePO4) battery from as low as 0.5 Volts. - Selectable, 4 charge programs: 1).12V Smart desulphation: 0.5V - 14.4V. 2). BMW CAN-bus compatible: 5V - 14.4V. 3). 12.8V Low Volt Recovery: 0.5V - 14.4V. 4). BMW CAN-bus compatible: 8.8V - 14.4V. - Charging Amps: 1.25A (constant current) - Indoor / Outdoor (lowest temperature: -40°F / -40°C) - Save: Low Volt Start of 0.5V + 2-step* desulphation recovery (*1-step low volt pulse save during CAN-bus mode) - For 4 x Lead Acid, AGM & GEL 12V batteries from 3 to 50Ah - Input: Global (100-240V 50-60Hz), high efficiency (CEC listed) - Weatherproof case with wall mounts - Incl. 6ft. / 180cm AC supply lead and 6ft. / 180cm charge lead ending in SAE connector. Weatherproof battery lead, battery clip set & hanging hook - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected.
Optimate
New

Tecmate, OptiMATE 4 Quad Program 12V battery charger

#993458

Stock:Yes

9-step 12V / 12.8V 1.25A sealed battery saving charger & maintainer for AGM, GEL & STD 12V and works with 12.8V Li-Ion made batteries with LiFe & LFP technology. Note: Quad program – select program 1 or 3 to charge battery direct or through a live (hot) 12V socket, or program 2 or 4 to charge through BMW CAN-bus controlled 12V socket. Will require optional cable accessory to connect to socket. - Fully automatic and safe charger / trickle charger for 24-7 use - BMW CAN-bus compatible, automatic activation - Smart desulphation from 0.5V, for Pb (conventional lead acid) batteries - Low voltage recovery & BMS reset, for LFP battery - Tests battery state of health - Energy saving technology - Stand-by power less than 0.5W - Efficient 24-7 battery maintenance - Weatherproof - Rated for use down to -40°C / -40°F - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected - Includes weatherproof battery lead, battery clip set & hanging hook.
Optimate
New

Tecmate, OptiMate 4 Quad Program

#998313

Stock:Yes

Bronze. 5-step 12V / 12.8V 2A sealed battery maintainer. For Lead Acid, AGM, GEL 12V batteries from 6 to 96Ah and 12.8/13.2V lithium (LiFePO4) batteries. It senses the battery condition, recharges and then keeps the battery 100% ready. The fully automatic maintenance program provides what the battery needs, never overcharges, never undercharges. - Charging Amps: 2A (constant current) - Charging volts: nominal: 12V & 12.8V range: 4V – 14.4V - Indoor / Outdoor (lowest temperature: -40°F / -20°C) - For Lead Acid, AGM & GEL 12V batteries from 3 – 96Ah - Input: Global (100-240V 50-60Hz), high efficiency (CEC listed), fully sealed - Weatherproof case with wall mounts - Incl. 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector - weatherproof battery lead & battery clip set - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term 24-7 battery maintenance - Automatic shut-down if short-circuited or battery disconnected
Optimate
New

Tecmate, Optimate, 2 Duo 12V battery charger. Bronze

#998339

Stock:Yes

UK wall plug. 2 bank charger 12V. Allows charging / maintaining 1 or 2 batteries at once. Dimensions: 11.5cm wide x 8.5cm high x 17.5cm deep.Microprocessor controlled, 100-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. CE approved. Note: When using multi-bank chargers, with the batteries in the bikes, you can order 990048 quick-disconnect cable which offers 25 foot (7.5 meters) of convenience.
Battery Tender

Battery Tender, International Plus - 1.25A charger

#990078

Stock:Yes

Std duty booster cables. 12ft. (3.65m), 8 gauge (3.26 ø mm). Soft blend PVC outer jacket for use with -40° to +140°F (-40° to 60°C). Comes with alligator style clamps.
Standard

Standard Co, Battery jumper cables 400A

#951768

Stock:No

Standard duty booster cables. 12ft. (3.65m), 4 gauge (5.19 ø mm). Soft blend PVC outer jacket for use with -40° to +140°F (-40° to 60°C). Comes with alligator style clamps.
Standard

Standard Co, Battery jumper cables 400A

#951769

Stock:Yes

UK wall plug. Charges all flooded, sealed, maintenance free, AGM and lead acid batteries. Water resistant and shock/vibration resistant with a weight less than 2kg. A compact and sturdy charger, ready for portable operations or permanent mounting in a garage etc. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved.
Battery Tender

Battery Tender, Power Tender 12V@5A High Efficiency

#501303

Stock:No

Bumper 10. Fits XS 0.8 chargers (906041 and 906042). This is a protective silicone rubber bumper that fits snugly around the charger body and offers additional grip and damage protection.
CTEK

CTEK, BUMPER10 protective charger bumper for 0.8A chargers

#906059

Stock:Yes

'The CONNECT - Clamp' is a 46cm long practical, quick and easy way to connect your CTEK charger to your battery. Perfect for moving your charger quickly between different batteries in workshops or showrooms. Comes with CTEK's 'Comfort Connect' connector to fit all CTEK products.
CTEK

CTEK, Comfort connect battery clamp

#906066

Stock:Yes

UK wall plug. 4.0A. Selectable 6/12V. Selectable Lithium or flooded, sealed, maintenance free, AGM and lead acid batteries. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved. Dimensions 17.2cm x 9.3cm x 4.9cm.
Battery Tender

Battery Tender, selectable charger. Lithium & 12/6V

#905508

Stock:No

Max 4A.
Shido

Shido, battery charge extension cable. 3 meters

#932963

Stock:Yes

CTEK’s charger BUMPER for CT5 Powersport chargers. This is a protective silicone rubber bumper that fits snugly around the charger body and offers additional grip and damage protection.
CTEK

CTEK, CT5 protective charger bumper

#906063

Stock:Yes

Bumper 60. Fits MSX chargers 3.8A (906046 / 906047) and 5.0A (906048 / 906049). This is a protective silicone rubber bumper that fits snugly around the charger body and offers additional grip and damage protection.
CTEK

CTEK, BUMPER60 protective charger bumper for 3.8&5A chargers

#906061

Stock:Yes

8A 12V charger. For 3Ah to 180Ah lead-acid (AGM, GEL, EFB, MF, CaCa) and lithium batteries. The CS ONE has APTO™ (Adaptive Charging) technology to recognise the type of battery you want to charge and tells how long it will need to charge it. There are no buttons on the CS ONE, just connect any lead-acid or lithium battery and simply charge. Polarity free clamps mean you don’t even need to worry about which clamp goes where, so you’ll never make a wrong connection again. The clamps are spark free too, so don’t worry if you accidentally touch them together Unlock additional features using the Bluetooth® enabled CTEK App. Select ‘RECOND’ to restore and recondition your battery. Choose ‘WAKE UP’ for lithium batteries with under voltage protection or to bring deeply discharged lead-acid batteries back to life. Select ‘SUPPLY’ to turn the CS ONE into a useful 12 V supply
CTEK

CTEK, CS ONE Battery charger. UK wall plug

#954369

Stock:Yes

With EU wall plug. 10-step 12.8V/13.2V 6A battery saving charger-tester-maintainer. The ultimate LiFePO4 / LPF Lithium Iron Phosphate) professional level battery diagnostic & maintenance charger and tester for batteries from 3 to 72 Amp-hour. - 10 steps: 1 low volt start (0.5V); 2 Test before charge; 3 Temperature check; 4 Ultra low volt save; 5 cell monitoring; 6 Test cell damage; 7 cel-balancing charge; 8 Optimize; 9 Test after charge; 10 24-7 maintenance - Starts from 0.5V with continuous monitoring / testing of charge acceptance or bad / shorted cell condition. Unnecessary (and unsafe) charging of a bad battery is prevented - Indoor / Outdoor (lowest temperature: -40°F / -40°C) - Input 100-240V 50-60Hz, high efficiency (CEC listed) - Weatherproof case with wall mounts, with 6ft / 180cm AC supply lead and 6ft / 180cm charge lead ending in SAE connector - Low Volt Start of 0.5V + 3 step low volt save & test - Includes weatherproof battery lead & battery clip set - No risk of overcharging - Sparks suppressed - Safe for vehicle electronics - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected
Optimate

Tecmate OptiMATE, Lithium 4S 6A battery charger

#941406

Stock:Yes

UK wall plug. 0.8A / 3.8A 12V charger. For 1.2Ah-85Ah lead-acid (AGM, GEL, EFB, MF, CaCa) batteries. With a mode button to switch between charging bike (0.8A) and car (3.8A) batteries. Offers a fully automated 7 step charge and maintenance sequence. Features include battery diagnosis to establish whether your battery can receive and retain a charge, a patented desulphation program and a 'Snowflake' program for charging on cold days. With CTEK's patented float/pulse system, which is the most efficient maintenance mode when a battery is connected for long periods. Simple to use and you can follow the whole charging process on the clear, easy to read display. - 12 volts. - 0.8A (bike) and 3.8A (car) modes. - Lead-acid batteries. -AGM mode. - 7 steps. - Clamps. - Eyelet connector. - Safe spark free operation. - Reverse polarity protected. - Splash and dust proof (IP65).
CTEK

CTEK, MXS 3.8 battery charger, UK

#906047

Stock:Yes

With EU wall plug. The power sport OEM recommended load tester, power desulphator and charger for all types of 12V lead-acid batteries. The BatteryMate has been saving batteries for 25 years! - New battery activation – 30 minute activation charge for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ‘dry-charged’ batteries that are delivered with a separate custom acid pack - True load tester selectable from 15A to 150A – Automatically tests battery cranking amps up to 330CCA. 3 second test simulates normal engine cranking / start, 15 second test checks battery health - Powersport specific charging algorithm – 4 step charging method recovers any 12V battery. MF mode allows up to 16.9V for ‘dry-charged’ AGM batteries - Temperature regulated charging – Charge voltage is adjusted according to ambient temperature. (-4mV/°C/cell above/below 68°F/20°C) - Accurate voltage sensing. Charge leads have integrated voltage sense wires for exact voltage measurement at the battery - Easy to use. 6 position combination selector allows selection of correct test and charge current for connected battery. TEST and then select max. charge time according to result, press 'charge' button. Program completes charging automatically and then tests the battery - Charging Amps: 9A maximum; 1, 2, 3, 5, 7, 9 Amp selection - Testing Amps: 150A maximum; 15, 35, 50, 70, 100, 150 Amp selection - Indoor / workshop environment (lowest temperature: -4°F / -20°C) - Save: Low Volt Start of 1V + high power desulphation recovery - For Lead Acid, AGM & GEL 12V batteries from 2 – 40Ah - Selectable 110-120VAC / 220-240VAC 50-60Hz - On/Off power switch and replaceable fuse protection - Vented industrial table top case - Incl. 6ft / 180cm AC supply lead and 1 pair high current 6ft / 180cm charge leads ending in heavy duty battery clamps - No risk of overcharging - Sparks suppressed - Safe for long-term battery maintenance - Automatic shut-down if short-circuited or battery disconnected
Optimate

Tecmate OptiMATE, BatteryMate 150/9 battery charger

#941415

Stock:Yes

With UK wall plug. Will charge 12V & 6V lead-acid, AGM and Lithium LiFePO4 batteries. Selectable 1A or 4A charging. With digital screen. Can be used as trickle charger. - Specific AGM mode for sealed batteries - Digital screen with live voltage reading - Hook attachment - Suitable for 6V and 12V batteries - 1A and 4A selectable charge - Clear split between Lithium and lead-acid charging modes and algorithms - Battery Recovery for deeply discharged batteries - Battery health check after charging - Maintaining mode, with 4 hour intervals voltage checks - Protected against reverse polarity, overcharging, overcurrent, overheating and short-circuits - User friendly detection for reverse polarity, low-voltage or damaged batteries - IP 65 splash and dust proof for outdoor use - Adjusts for varying A/C line voltage and delivers consistent charging current - 8 step lead acid charging - 7-step Lithium charging - Input: 220-240V AC 50-60Hz - Output: 6V or 12V 1A or 4A DC - Dimensions: 210 x 87 x 50mm - Weight: 0.6 kg - IP rating: IP 65 - Battery: 4-80 Ah > Charge, 4 - 120 Ah > Maintenance
Shido

Shido, dual battery charger 12V/6V DC 4.0 (UK)

#932960

Stock:Yes

With EU wall plug. Professional variable 0.4A to 10A 12V diagnostic battery charger-tester & power supply for powersport & small craft / machine professionals, repair shops and battery retailers. - Pro use: 12V lead-acid STD & AGM from 3-50Ah and 12.8V/13.2V Lithium LFP (LiFePO4) from 2-20Ah. - Normal use: 12V lead-acid STD & AGM from 3-240Ah and 12.8V/13.2V Lithium LFP (LiFePO4) from 2-120Ah. - Charging Amps: 0.4A to 10A variable (Ampmatic) - Charging Volts: 12V lead-acid: 0.5V to 22V. 12.8V/13.2V Lithium LFP (LiFePO4): 0.5V to 14.4V. Powersupply: 11V to 13.6V. - Operation: selectable - 11 step charger - 3 Selections: Select a charge mode for 12V lead-acid OR 12.8V LiFePO4, or select PowerSupply mode for battery support during vehicle diagnostics, tuning or troubleshooting - Automatic fast battery activation: flashing green test light indicates battery is healthy and sufficiently charged - Smart recovery mode for deep discharged batteries, a bad battery is quickly identified, a good battery receives charge is retested after - Pushbutton activated BMS reset for LiFePO4 batteries - Test indication for GOOD (80 to 100%), OK (60 to 80%) and BAD (below 60%) batteries - Powersupply mode provides constant power for vehicle tuning, diagnostics and troubleshooting - Case with rubber bumbers, with wall-mount or hanger bars. AC Class 2 input socket, with ON/OFF switch, 15cm / 6" output cord - Certification - CE, UKCA, NRTL (UL & CSA), PSE (Japan), SAA (Aus & NZ) - Indoor use. IP40 rating - Included cables: Class II AC cord suitable for region, O-43 charge lead extender 180cm/72" and O-14 fused battery clips - Vehicle hanging hook and wall receiver included
Optimate

Tecmate OptiMATE, Pro 1 DUO 12B 10A battery charger

#958059

Stock:Yes

UK wall plug. 12V 0.8A. For up to 10Ah batteries. Selectable Lithium or flooded, sealed, maintenance free, AGM and lead acid batteries. Microprocessor controlled, 110-240V compatible. Adapts to battery needs and offers fully automatic 4-stage charging program, initialization / bulk charge / absorption mode / float mode, as required. A red LED indicates a 'dead' battery or something else when the battery is unable to take the charge. A green LED blinks during the charging process, until the battery is at least 80% charged. A constant lighting green LED indicates the battery is ready for use. CE approved. Dimensions 8.3cm x 5cm x 3.5cm.
Battery Tender

Battery Tender, Junior 800 - selectable (UK)

#905503

Stock:No