Parts - Electrical - Switches

Brand name

36

Segment

4

Pins

8

Material

7

Position

6

Product type

6

Voltage

2

Finish

8

Color

7

Length

13

Ampere

13

20 of 258 search results

Sort on:

SORT ON:

Banjo bolt, M10 x 1.25 threaded, with incorporated hydraulic brake light switch with wiring. High polished stainless steel. 30mm under hex

Goodridge, M10 x 1.25 double banjo brake switch. SS

#708069

Stock:Yes

Used to install motorcycle lights as turn signals, tail/brake lights and position lights. Offers an electronic universal installation solution. Compatible with all motorcycles, from classics to bikes equipped with the latest operating systems.
- Allows installation of 4 turn signals, taillight, brake light & position lights on 12V bikes
- Corrects flashing frequency
- Does not trigger error codes or warning lights
- No disturbing fluctuating currents
- For installation of flashers with lower or higher power consumption (Watt) than OEM
- For installation of indicators with higher voltage (Volt) than OEM since, on some bikes with a 12 volt system, the indicators are controlled with a lower (like 6V) voltage
- Allows installation of minus-switched turn signals
- Rotary switches allow required flashing frequency settings
Note: See 710413 for i.NEX-AddOn for use on Indian motorcycles

Kellerman, i.Nex - V12, equalizer

#996466

Stock:Yes

Multiple function handlebar switch relay that will allow you to switch not just one function, like a regular relay, but virtually all functions that are found on a motorcycle. With installed wires for each function.
- Input Current: up to 12V/20A
- Input line fuse protected
- CE approved
- With individual cables for following functions: Headlight HI/LOW, Horn, Start, Turn signal left, Turn signal right, Hazard lights
- 4 additional connections & functions
- Each function is short-circuit protected
- Dimensions 75mm x 30mm x 20mm
Note: Perfect to combine with one or two of Daytona's 701156 black/chrome or 701154 black/black 3-button handlebar switch(es) to control it all.

Daytona, multifunctional handlebar switch relay EZ

#701157

Stock:No

Banjo bolt, M10 x 1.00 threaded, with incorporated hydraulic brake light switch with wiring. High polished stainless steel. 18mm under hex

Goodridge, M10 x 1.00 banjo brake switch. SS

#708066

Stock:Yes

High polished stainless steel hose end to hose end.
With male 3/8-24 an-3 on both sides.
On top threaded to fit 1/8" NPT threaded hydraulic brake switch

Goodridge, universal brake switch fitting. 1/8 NPT. SS

#999446

Stock:Yes

Banjo bolt, 3/8-24 threaded, with incorporated brake light switch. High polished stainless steel. 18mm under hex

Goodridge, hydraulic brake light switch. SS

#708064

Stock:Yes

Polished finished forged brass housing. With 2 polished stainless steel momentary push button switches. Great radical-retro looks on its own and perfect to style-match with Kustom Tech's handlebar controls.

Note: See 532395 for stock replacement polished stainless Kustom Tech micro switch only.

Kustom Tech, Deluxe handlebar switch. Dual button

#532452

Stock:Yes

Satin finished forged brass housing. With 2 polished stainless steel momentary push button switches. Great radical-retro looks on its own and perfect to style-match with Kustom Tech's handlebar controls.

Note: See 532395 for stock replacement polished stainless Kustom Tech micro switch only.

Kustom Tech, Deluxe handlebar switch. Dual button

#532453

Stock:Yes

Control your accent lighting and additional motorcycle accessories at the tip of your fingers with these master cylinder Accessory Switches. Rated for 12V and up to 10-Amp accessories each, these switches add convenience and style to controlling auxiliary lighting and other accessories on your motorcycle.

Kuryakyn, Accessory switches for m/c reservoir covers

#8081072

Stock:Yes

Plug-in module for rear side that adds a rapid three time 'flash' when braking, and a run-turn-brake function to single filament OEM and halogen lights. If you do not want the flashing brake function, it can be turned off by unplugging the connector marked 'flashing'.
Note: A load equalizer is not required.
Note: Not compatible with Kuryakyn Panacea taillights.
Note: For 04-13 XL see 968343 adapter, which allows installation of 968344 'The Flasher' on these non CAN-bus Sportster models.

Cycle Visions, The Flasher plug-in module

#968344

Stock:Yes

Tension sensor, push.
M6 to 5/16 UNF.
Quick Shifter to allow full throttle shifting, without using the clutch.
The fuel and/or ignition system are momentarily shut down, to unload the transmission.
At that moment it is relatively easy to make clutch-less shifts.
- The Quick-Shifter works in combination with the Dynojet Power Commander PCIIIUSB fuel control modules
- Power Commander PCIIIUSB fuel control modules is fully programmable through the Power Commander module with supplied software
- The user can set the 'kill time' but also a minimum RPM to function, so the system does not kick-in during cruising
- No need for cutting or splicing wires when installing this kit
- Tension sensors work with shifter rod pressure
- It mounts inline with the shifter rod and is available in push or pull style
- The appropriate shifter rod depends on the application and is, therefore, not included and must be supplied by the user

**Dynojet product not available to purchase by Dealers located in the UK**

Dynojet, Quick Shifter. Tension sensor - push

#939001

Stock:Yes

Not lighted. Direct replacement switch housing switches, complete kit for models equipped with radio & cruise control. Incl. brake light switch, terminals and hardware. Ready to install. Complete with pre-installed 60" (152cm) wiring for stock applications.

Handlebar switch & wiring kit. Radio/Cruise. Chrome

#920159

Stock:Yes

Not lighted. Direct replacement switch housing switches. Incl. brake light switch, terminals and hardware. Ready to install. Complete with pre-installed 60" (152cm) wiring for stock applications.

Handlebar switch & wiring kit. Standard. Chrome

#920181

Stock:Yes

Not lighted. Direct replacement switch housing switches, complete kit for radio equipped models. Incl. brake light switch, terminals and hardware. Ready to install. Complete with pre-installed 60" (152cm) wiring for stock applications.

Handlebar switch & wiring kit. Radio. Black

#920150

Stock:Yes

Not lighted. Direct replacement switch housing switches, complete kit for radio equipped models. Incl. brake light switch, terminals and hardware. Ready to install. Complete with pre-installed 60" (152cm) wiring for stock applications.

Handlebar switch & wiring kit. Radio. Chrome

#920149

Stock:Yes

Not lighted. Direct replacement switch housing switches, complete kit for models equipped with cruise control. Incl. brake light switch, terminals and hardware. Ready to install. Complete with pre-installed 60" (152cm) wiring for stock applications.

Handlebar switch & wiring kit. Cruise. Black

#920152

Stock:No

Black CC (Black Contrast Cut) is aluminum with a black anodized finish and a contrast machined finish. CNC machined.

Covingtons, Touring finned ignition switch cover. Black CC

#953806

Stock:Yes

Chrome plated billet aluminum in the 10-gauge design. Direct replacement for the stock cover. Incl. chrome hardware.

Arlen Ness, 10-gauge ignition switch cover chrome

#569827

Stock:Yes

Black Ops, a dual tone gloss black with black wrinkle finish.

PM, Radial can-bus brake light switch actuator. Black Ops

#599233

Stock:No

This complete kit comes with all switches and allows you renew your old wires, or replace them when installing higher/wider handlebars. Incl. brake light switch. OEM color coded for ease in installation. Total length of the extra long wires is approx. 47" (120cm).

Handlebar wire & switch kit. Chrome switches

#910086

Stock:No