20 of 228 search results

SORT ON:

Used to install & remove the outboard balancer bearing on chain guide support plate. Also installs a new balancer bearing and counter balancer shaft.
MCS
New

MCS, balancer bearing tool kit

#987917

Stock:Yes

Removes and installs 25344-99 / 921146 pinion shaft bushing in the cam support plate. After 2010 these bushings are no longer used.
MCS
New

MCS, pinion shaft bushing remover/installer tool

#987926

Stock:Yes

Used to install the oil pump seal into the oil pump housing, below gear surface. Prevents installation damage to seal.
MCS
New

MCS, oil pump seal install tool

#987920

Stock:Yes

Used to remove and install the 25400447 VVT cam phaser central bolt (spool valve bolt) assembly for access to the cam support plate, oil pump and the camshaft.
Feuling
New

Feuling, cam phaser bolt tool

#707253

Stock:No

Used to lock flywheel, of assembled engine. Installs through crank position sensor. Great for use with compression leakdown testing and other service operations where flywheel must be locked. Note: Incl. highly visible red 'Danger, do not operate' card to prevent someone starting engine.
Jims

JIMS, 'Mighty Bite' flywheel lock

#962032

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 19mm

#580882

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 13.8mm

#580884

Stock:Yes

Used to install 989244 crankcase nuts.
Colony

Colony nut install tool

#989245

Stock:Yes

Removes & installs the right (sprocket shaft) side crankshaft bearing on Twin Cam A engines (Dyna & Touring)
Jims

JIMS, crankshaft bearing tool

#978222

Stock:Yes

Removes & Installs left sprocket & right pinion crankshaft bearing on Twin Cam A engines (Dyna & Touring). Removes & installs left (sprocket shaft) side crankcase bearing on Twin Cam B engines (Softails)
Jims

JIMS, crankshaft bearing tool

#978246

Stock:Yes

Used to install and remove sprocket shaft bearing race from left side crankcase; Note: Used with 920542 JIMS driver handle
Jims

JIMS, sprocket shaft bearing race tool

#978337

Stock:No

Used to remove OEM 11000134 / 568378 sprocket shaft seal / crankshaft main seal from left engine case without damage. Pulls seal square to the bore by turning a wrench. Note: See 559403 for JIMS installer tool.
Jims

JIMS, sprocket shaft seal puller tool

#569209

Stock:Yes

Used to lock flywheel, of assembled engine. Installs through crank position sensor. Great for use with compression leakdown testing and other service operations where flywheels must be locked. Note: Incl. highly visible red 'Danger, do not operate' card to prevent someone starting engine.
Jims

JIMS, 'Mighty Bite' flywheel lock

#559408

Stock:Yes

Used to install and remove OEM 601 roll pin in the oil pump.
Feuling

Feuling, oil pump roll pin remover/installer tool

#588059

Stock:Yes

Used to bench test Feuling M8 oil pumps (tester will not fit OEM M8 pumps). Used for PSI pressure opens the relief valve. The spring tension can be adjusted to achieve the desired pop-off PSI. Tool includes: air regulator, 0 - 100 psi pressure gauge, plugs for water and oil cooled oil pumps, gasket & needed hardware. Feuling® recommends the oil pump relief valve be seated and sealed from 0-30 psi with full pop-off at 50-60 psi. Note: Will not fit OEM pumps.
Feuling

Feuling, oil pump pressure tester

#588061

Stock:Yes

Used to ream the pressure relief valve seat of the cam plate in all Twin Cam engines and in the oil pump of M8 engines. Compatible with OEM and aftermarket cam plates. Feuling recommends a new relief valve as Feuling 566110 relief valve, spring & roll pin kit. Note: Can be used with 566117 (Twin Cam cam plate) and 588061 (M8 oil pump) pressure relief valve test tools.
Feuling

Feuling, cam plate/oil pump reamer tool

#588062

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 21mm

#580881

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 17mm

#580883

Stock:Yes

Must be ordered separately for 978324 JIMS sprocket shaft seal installer tool. Is included with 978325 JIMS maindrive seal installer tool.
Jims

JIMS, driver handle

#576558

Stock:Yes

Used to remove the (right side) cam gear cover without force of hammers or screwdrivers.
Motion Pro

Motion Pro, nose cone puller

#547204

Stock:Yes